Hand pumps · Made in Finland
Nira 9 Hand Pump for Large Volumes of Oil, Diesel and Water
Image 1 of 2 · Nira 9 hand pump – 1¼" flanges · nitrile
Our largest lever hand pump.
The Nira 9 moves larger volumes – about 60 l/min (≈ 15.9 US gal/min) – of diesel, oils, glycol and water by hand. 1¼" or 1½" threaded flanges, no electricity needed.
- Pumping capacity
- 60 l/min≈ 15.9 US gal/min
- Suction height with a bottom valve
- Up to 8 m≈ 26 ft
- Frost resistance
- -15 °C5 °F
Manual & CAD downloads Where to buy
Product description
High capacity by hand
With nitrile seals the Nira 9 pumps diesel, oils, glycol and water. Brisk pumping gives about 60 l/min (≈ 15.9 US gal/min). The pump is also available with Viton seals for petrol (gasoline) – ask for a quote.
The Nira 9 is mostly rustproof, but the rocker linkage inside can rust, which should be taken into account if you pump water.
Installation
The suction height is 4 m (≈ 13 ft) without a bottom valve and 8 m (≈ 26 ft) with a bottom valve. The length of the suction pipe affects the suction height: 10 m (≈ 33 ft) of horizontal suction pipe reduces it by about 1 m (≈ 3 ft). A 32 mm (≈ 1.3 in) or 40 mm (≈ 1.6 in) rigid pipe is normally used as the suction pipe. A garden-hose type pipe is too soft and collapses under suction.
The pump withstands a momentary pressure of approx. 3 bar (≈ 44 psi) but must not be installed in a network where it is constantly under pressure.
Use and care
Water remains inside the pump after use, so it is not recommended for drinking water. If the pump is used for water where it can freeze, empty it before frost.
Technical specifications
The essentials, all in one place.
| Suitability | Water, oil, fuel oil, diesel, glycol |
|---|---|
| Pumping capacity | 60 l/min (≈ 15.9 US gal/min) |
| Suction height | 4 m (≈ 13 ft) without bottom valve, 8 m (≈ 26 ft) with bottom valve |
| Pressure | 1 bar (≈ 14.5 psi) |
| Frost resistance | -15 °C (5 °F) |
| Material | Silumin casting, steel, stainless steel, nitrile rubber |
| Weight | 5.8 kg (≈ 12.8 lb) |
| Packaging | Plastic packaging |
| Country of origin | Finland |
| Warranty | 2 years |
Values for version 1120 – 1¼" flanges · nitrile.
Choose for your application
- Large tanks
- Agriculture
- Industry
Match the seal material to your liquid before ordering – see liquid suitability.
Important for installation
- Not suitable for drinking water: water remains inside the pump after use.
- If the pump is used for water, empty it completely before the temperature drops below 0 °C (32 °F): disconnect the suction pipe and pump until the pump is dry.
- The pump must not be installed in a network where it is constantly under pressure. It withstands a momentary pressure of approx. 3 bar (≈ 44 psi).
- When the pump is attached to a fuel tank, make sure the tank cannot empty itself (the siphon effect).
Liquid suitability
Compare seal materials before selecting your pump.
| Seal material | Water* | Diesel | Oils | Special application |
|---|---|---|---|---|
| Nitrile | Suitable | Suitable | Suitable | Glycol |
| Viton | Suitable | Suitable | Suitable | Petrol (gasoline) |
| ECO | Not suitable | Suitable | Suitable | Cold conditions |
| EPDM | Suitable | Not suitable | Not suitable | Acetone (limited) |
* Never for drinking water with Nira 2, Nira 6B or Nira 9. ECO seals are not suitable for pumping drinking water.
Available for this pump: Nitrile, Viton. EPDM: Nira 6B hand pump, Nira 2 barrel pump
The information is for reference only; comprehensive knowledge of material suitability requires testing. Confirm the liquid, concentration, temperature and pump version with Nira.
Downloads & resources
Everything you need to plan, install and maintain.
3D CAD · STEP
3D STEP model
For planning your installation
2.5 MB
Spare parts · Drawing
Nira 9 spare parts
Exploded-view drawing of the pump
PDF · Norsk
Product card
399 KB
Let’s find the right pump.
Tell us what you need to pump. We’ll help you choose the pump and seals.
Phone +358 10 830 6759 · Email nira.info@nira.fi