Hand pumps · Made in Finland
Nira 6B Hand Pump for Fuel, Oil and Water
Image 1 of 8 · Nira 6B hand pump – 1" flanges · nitrile · lever up
Reliable pumping. Wherever you need it.
A durable lever-operated hand pump for transferring water, diesel, fuel oil, oils and glycol – on a tank, at the waterfront or as a backup when the power is out. No electricity needed.
- Pumping capacity
- 40 l/min≈ 10.6 US gal/min
- Suction height with a bottom valve
- Up to 8 m≈ 26 ft
- Frost resistance
- -15 °C5 °F
Manual & CAD downloads Where to buy
Product description
For everyday use and demanding applications
With nitrile seals the Nira 6B pumps water, diesel, fuel oil, oils and glycol. Typical uses are fuel and oil tanks, agriculture, industry, gardens and waterfront saunas. It can lift water from a well, a lake or the sea, empty a basement or a flooded pit, or transfer liquids from one tank to another.
The Nira 6B has been manufactured in Finland since the 1960s, and many pumps from the early years are still in use. Because it works without electricity, it is also a dependable backup for an electric pump during a power cut.
Simple operation and installation
Move the lever back and forth to pump. The pump is delivered assembled: connect the pipes to the upper and lower threaded flanges (¾" or 1"). The suction height is 4 m (≈ 13 ft) without a bottom valve and 8 m (≈ 26 ft) with a bottom valve at the end of the suction pipe.
Use a rigid plastic suction pipe or a reinforced 32 mm (≈ 1.3 in) water hose – an ordinary garden hose is too soft and collapses under suction. When tightening connectors, support the pump so that the torque does not act on the pump body. Pipes and fittings are not included with the pump; the installation set includes two straight connectors, an elbow connector, a bottom valve and screws for wall mounting.
Seal options and construction
Nitrile seals suit water, diesel, oils and glycol down to -15 °C (5 °F). EPDM seals suit acetone and ethanol-based geothermal fluids with corrosion inhibitors down to -30 °C (-22 °F), but not oils. For petrol (gasoline), choose the Nira 6B Viton; for cold conditions, see the cold-weather hand pumps.
The standard Nira 6B is mostly rustproof, but the rocker linkage inside can rust. In the fully stainless version all parts, including the rocker linkage, are stainless.
Use and care
The pump does not drain after use, so it is not suitable for drinking water. If you pump water and the pump is kept where it can freeze, empty it before frost. The pump needs no regular maintenance, and all parts are available as spare parts.
Technical specifications
The essentials, all in one place.
| Suitability | Water, oil, fuel oil, diesel, glycol |
|---|---|
| Pumping capacity | 40 l/min (≈ 10.6 US gal/min) |
| Suction height | 4 m (≈ 13 ft) without bottom valve, 8 m (≈ 26 ft) with bottom valve |
| Pressure | 1 bar (≈ 14.5 psi) |
| Frost resistance | -15 °C (5 °F) |
| Material | Silumin casting, steel, stainless steel, nitrile rubber |
| Weight | 3.30 kg (≈ 7.3 lb) |
| Package dimensions | 52 x 25 x 15 cm (≈ 20.5 x 9.8 x 5.9 in) |
| Country of origin | Finland |
| Warranty | 2 years |
Values for version 1101 – 1" flanges · nitrile · lever up.
Choose for your application
- Fuel and oil tanks
- Agriculture
- Industry
- Waterfront saunas and cabins
- Backup pumping
- Cooling/heating systems
Match the seal material to your liquid before ordering – see liquid suitability.
Important for installation
- Not suitable for drinking water: water remains inside the pump after use.
- If the pump is used for water, empty it completely before the temperature drops below 0 °C (32 °F): disconnect the suction pipe and pump until the pump is dry.
- The pump must not be installed in a network where it is constantly under pressure. It withstands a momentary pressure of approx. 3 bar (≈ 44 psi).
- When the pump is attached to a fuel tank, make sure the tank cannot empty itself (the siphon effect).
- The lever direction (up or down) is chosen when ordering and cannot be changed afterwards.
- EPDM seals are not suitable for oils or other oil-based liquids.
Liquid suitability
Compare seal materials before selecting your pump.
| Seal material | Water* | Diesel | Oils | Special application |
|---|---|---|---|---|
| Nitrile | Suitable | Suitable | Suitable | Glycol |
| Viton | Suitable | Suitable | Suitable | Petrol (gasoline) |
| ECO | Not suitable | Suitable | Suitable | Cold conditions |
| EPDM | Suitable | Not suitable | Not suitable | Acetone (limited) |
* Never for drinking water with Nira 2, Nira 6B or Nira 9. ECO seals are not suitable for pumping drinking water.
Available for this pump: Nitrile, EPDM. Viton: Nira 6B Viton hand pump, Nira 9 hand pump · ECO: Nira 6B Arctic hand pump
The information is for reference only; comprehensive knowledge of material suitability requires testing. Confirm the liquid, concentration, temperature and pump version with Nira.
Videos
See the pump in use and how to install it.
Nira 6b installation
YouTube
Nira 6b water pump
YouTube
Downloads & resources
Everything you need to plan, install and maintain.
PDF · English
Instruction manual
Installation, use and maintenance
3.0 MB
3D CAD · STEP
3D STEP model
For planning your installation
746 KB
Spare parts · Drawing
Nira 6B spare parts
Exploded-view drawing of the pump
PDF · English
Product card
572 KB
Let’s find the right pump.
Tell us what you need to pump. We’ll help you choose the pump and seals.
Phone +358 10 830 6759 · Email nira.info@nira.fi